Demo setup

• 
• Topologies
• Daisy chain
• Star

Sanity test cases

• #	Test case Name	Test steps	Status(PASS/FAIL)

Backhaul combination for daisy chain

• Controller to Agent 1	Agent 1 to Agent 2	Dependencies	status
  5Ghz	2.4Ghz
  5Ghz	5Ghz	Need ACL support
  5Ghz	6Ghz	6Ghz BH not working
  6Ghz	6Ghz	Need ACL support

Wireless client connectivity(Mobile Phone)

• TBD

SSID  change 

• TBD

Reference InterfaceMap 

• 5G-5G
  • 
• 5G-2G
  • 

Key insights to follow

• Dedicate serial cable for each banana pi device.Never remove serial cable when the device is running
• Make sure you remove the case when performing EM testing
• Make sure we connect all antennas
• Never leave board in Power on condition if you are not there with device or make sure you check the board status through camera.

Validation stages

• Stage 1 (gateway + colocated Agent)

  • Test results (If any of the test case case fails.then we are not allowed to goto stage 2)

    • stage #	Test case #	Test case Name	Priority	Test case Description	Status
      1	0	Boot the device and wait until all radios are up and running configure DB and mesh configuration in nvram remove wifi db /opt/secure/wifi/* Need to have updated one_wifi_prestart.sh need to have aishwarya Mac address changes restart onewifi wifi reset in DB using cli and update brlan0 mac address in colocated agent	stage 2 blocker
      1	1	Bringup controller and colocated agent start em controller start em agent restart em controller  restart em agent	stage 2 blocker
      1	2	Make sure onewifi is up and running	stage 2 blocker
      1	3	Make sure em_ctrl is up and running	stage 2 blocker
      1	4	Make sure em_agent is up and running	stage 2 blocker
      1	5	All wifi interfaces/VAP's should have standard mac address using aishwarya change	stage 2 blocker
      1	6	Reboot the device and onewifi/ctrl/agent should be up and running with persistent configuration in EasyMeshconfig.json and InterfaceMap.json & standard serial number No DB crash should observe Cli should not crash  play around with cli without changing any values j,k,q	stage 2 blocker
      1	7	changes ssid  from cli and check iw dev after 2mins New ssid should reflect in all 3 radios No crash of controller/agent/Onewifi should happen No kernel panic	stage 2 blocker
      1	8.1	Wait for 3 mins New ssid should persistent in all 3 radios No crash of controller/agent/Onewifi should happen No kernel panic	stage 2 blocker
      1	8.2	Wait for 3 mins New ssid should persistent in all 3 radios No crash of controller/agent/Onewifi should happen No kernel panic	stage 2 blocker
      1	8.3	Wait for 3 mins New ssid should persistent in all 3 radios No crash of controller/agent/Onewifi should happen No kernel panic	stage 2 blocker
      1	8.4	Wait for 3 mins New ssid should persistent in all 3 radios No crash of controller/agent/Onewifi should happen No kernel panic	stage 2 blocker
      1	8.5	Wait for 3 mins New ssid should persistent in all 3 radios No crash of controller/agent/Onewifi should happen No kernel panic	stage 2 blocker
      1	9	connect Mobile phone to private ssid's (Try with 2.4Ghz first)  connection should be successful Internet browsing should work No crash of controller/agent/Onewifi should happen No kernel panic	stage 2 blocker
      1	10	connect Mobile phone to private ssid's (Try with 5Ghz)  connection should be successful Internet browsing should work No crash of controller/agent/Onewifi should happen No kernel panic	stage 2 blocker
      1	11	connect Mobile phone to private ssid's (Try with 6Ghz)  connection should be successful Internet browsing should work No crash of controller/agent/Onewifi should happen No kernel panic	stage 2 blocker
      1	12	Disconnect all client and keep device idle for 15 mins	stage 2 blocker
      1	13	Check iw dev after 15 mins and all radios should have the same ssid	stage 2 blocker
      1	14	Try connecting to 2.4ghz/5ghz/6ghz individually and verify internet connection. connection should be successful Internet browsing should work No crash of controller/agent/Onewifi should happen No kernel panic	stage 2 blocker
      1	15	Reboot the device & Try test case 14 & No issues should observe	stage 2 blocker
      1	16	Repeat test case 15 for 15 times with a time interval  Reboot command from terminal. Hard reset	stage 2 blocker
      1	17	Factory reset the device	Future	TBD
      1	18	Repeat from test case 7 till test case 16 with passcode change and channel change	Future

• Stage 2 - Onboard Remote Agent 1 

  • Prerequisite for stage 2
    • There should not be any issues in stage 1.

  • Test results (If any of the test case case fails.then we are not allowed to goto stage 3)

    • stage #	Test case #	Test case Name	Priority	Test case Description	Status
      2	0	Boot the device and wait until all radios are up and running remove dnsmasq from /usr/bin ifconfig erouter0 down Do mesh configuration in nvram ----- make sure you make colocated mode 0  remove wifi db /opt/secure/wifi/* (till Agent profile is up and running by Akhil P ) Need to have updated one_wifi_prestart.sh need to have aishwarya Mac address changes restart onewifi	stage 3 blocker
      2	1	Make sure onewifi is up and running	stage 3 blocker
      2	2	validate  iw dev wifi1.1 info  in Extender 1 iw dev wifi1.1.sta1 info in ctrl iw dev wifi1.1.sta1 station dump in ctrl Agent 1 device should communicate with gateway all the time	stage 3 blocker
      2	3	Bringup Easymesh agent check iw dev Agent 1 should show all ssid details for all radios set brlan0 with static ip Perform ping test/wget http://10.0.0.1	stage 3 blocker
      2	4	Disable all private VAP's in gateway side & disable 5Ghz and 6Ghz radio in agent 1 device connect Mobile phone to private ssid's (Try with 2Ghz)  connection should be successful Internet browsing should work No crash of agent/Onewifi should happen No kernel panic	stage 3 blocker
      2	5	Disable all private VAP's in gateway side & disable 2.4Ghz and 6Ghz radio in agent 1 device connect Mobile phone to private ssid's (Try with 5Ghz)  connection should be successful Internet browsing should work No crash of agent/Onewifi should happen No kernel panic	stage 3 blocker
      2	6	Disable all private VAP's in gateway side & disable 2.4Ghz and 5Ghz radio in agent 1 device connect Mobile phone to private ssid's (Try with 6Ghz)  connection should be successful Internet browsing should work No crash of agent/Onewifi should happen No kernel panic	stage 3 blocker
      2	7	Leave the device idle for 5 mins & check Agent 1 connectivity with gateway.there should not be any disconnection over BH	stage 3 blocker
      2	8	Reboot the agent 1 & check if agent 1 connect to controller and stable Monitor for 5 mins and see if BH connection is stable	stage 3 blocker
      2	9	Repeat test case 4,5,6	stage 3 blocker
      2	10	Reboot the device and Agent1 should automatically connect to gateway & client connectivity and internet browsing should happen & no kernel crash/EM agent/onewifi crash	stage 3 blocker
      2	11	Power off the gateway and wait for gateway to up and running and check if Agent 1 onboards to controller via BH without any issues	stage 3 blocker
      2	12	Repeat test case 4,5,6	Stage 3 blocker
      2	13	Change ssid in gateway using cli and wait for 2 to 3 mins and check if same is reflected in agent 1 .if its reflected  Repeat test case 4,5,6	Stage 3 blocker

• Stage 3 - Onboard Remote Agent 2 to Remote Agent 1 (Daisy chain)

  • Prerequisite for stage 3
    • There should not be any issues in stage 2.

    • stage #	Test case #	Test case Name	Priority	Test case Description	Status
      3	0	Boot the device and wait until all radios are up and running remove dnsmasq from /usr/bin ifconfig erouter0 down Do mesh configuration in nvram ---------- make sure you make colocated mode 0 remove wifi db /opt/secure/wifi/* (till Agent profile is up and running by Akhil P ) Need to have updated one_wifi_prestart.sh need to have aishwarya Mac address changes restart onewifi	stage 4 blocker
      3	1	Make sure onewifi is up and running	stage 4 blocker
      3	2	validate  iw dev wifi0.1 info  in Agent 2 iw dev wifi0.1.sta1 info in Agent 1 iw dev wifi0.1.sta1 station dump in Agent 1  Agent 2 device should communicate with Agent 1 all the time	stage 4 blocker
      3	3	Bringup Easymesh agent check iw dev Agent 2 should show all ssid details for all radios which is common across gateway/agent1 and agent2 set brlan0 with static ip Perform ping test/wget http://10.0.0.1	stage 4 blocker
      3	4	Disable all private VAP's in gateway side & Agent 1 & disable 5Ghz and 6Ghz radio in agent 2 device connect Mobile phone to private ssid's (Try with 2Ghz)  connection should be successful Internet browsing should work No crash of agent/Onewifi should happen No kernel panic	stage 4 blocker
      3	5	Disable all private VAP's in gateway side & Agent 1 & disable 2.4Ghz and 6Ghz radio in agent 2 device connect Mobile phone to private ssid's (Try with 5Ghz)  connection should be successful Internet browsing should work No crash of agent/Onewifi should happen No kernel panic	stage 4 blocker
      3	6	Disable all private VAP's in gateway side  & Agent 1 & disable 2.4Ghz and 5Ghz radio in agent 2 device connect Mobile phone to private ssid's (Try with 6Ghz)  connection should be successful Internet browsing should work No crash of agent/Onewifi should happen No kernel panic	stage 4 blocker
      3	7	Leave the device idle for 5 mins & check Agent 2 connectivity with Agent 1.there should not be any disconnection over BH	stage 4 blocker
      3	8	Reboot the agent 2 & check if agent 2 connect to Agent 1 and stable Monitor for 5 mins and see if BH connection is stable	stage 4 blocker
      3	9	Repeat test case 4,5,6	stage 4 blocker
      3	10	Reboot the device and Agent2 should automatically connect to Agent 1 & client connectivity and internet browsing should happen & no kernel crash/EM agent/onewifi crash	stage 4 blocker
      3	11	Power off the agent 1  and wait for agent 1 to up & running and let it onboard to gateway  and check if Agent 2 onboards to Agent 2 via BH without any issues	stage 4 blocker
      3	12	Repeat test case 4,5,6	Stage 4 blocker
      3	13	Change ssid in gateway using cli and wait for 2 to 3 mins and check if same is reflected in agent 2 .if its reflected  Repeat test case 4,5,6	Stage 4 blocker

• Stage 4 - Onboard Remote Agent 3 to Gateway(star)

  • Prerequisite for stage 4
    • There should not be any issues in stage 3 .

  • Test results (If any of the test case case fails.then we are not allowed to goto stage 5)

    • stage #	Test case #	Test case Name	Priority	Test case Description	Status
      4	0	Boot the device and wait until all radios are up and running remove dnsmasq from /usr/bin ifconfig erouter0 down Do mesh configuration in nvram ---------- make sure you make colocated mode 0 remove wifi db /opt/secure/wifi/* (till Agent profile is up and running by Akhil P ) Need to have updated one_wifi_prestart.sh need to have aishwarya Mac address changes restart onewifi	stage 5 blocker
      4	1	Make sure onewifi is up and running	stage 5 blocker
      4	2	validate  iw dev wifi1.1 info  in Extender 3 iw dev wifi1.1.sta2 info in ctrl iw dev wifi1.1.sta2 station dump in ctrl Agent 3 device should communicate with gateway all the time	stage 5 blocker
      4	3	Bringup Easymesh agent check iw dev Agent 3 should show all ssid details for all radios set brlan0 with static ip Perform ping test/wget http://10.0.0.1	stage 5 blocker
      4	4	Disable all private VAP's in gateway side & disable 5Ghz and 6Ghz radio in agent 3 device connect Mobile phone to private ssid's (Try with 2Ghz)  connection should be successful Internet browsing should work No crash of agent/Onewifi should happen No kernel panic	stage 5 blocker
      4	5	Disable all private VAP's in gateway side & disable 2.4Ghz and 6Ghz radio in agent 3 device connect Mobile phone to private ssid's (Try with 5Ghz)  connection should be successful Internet browsing should work No crash of agent/Onewifi should happen No kernel panic	stage 5 blocker
      4	6	Disable all private VAP's in gateway side & disable 2.4Ghz and 5Ghz radio in agent 3 device connect Mobile phone to private ssid's (Try with 6Ghz)  connection should be successful Internet browsing should work No crash of agent/Onewifi should happen No kernel panic	stage 5 blocker
      4	7	Leave the device idle for 5 mins & check Agent 3 connectivity with gateway.there should not be any disconnection over BH	stage 5 blocker
      4	8	Reboot the agent 3  & check if agent 3 connect to controller and stable Monitor for 5 mins and see if BH connection is stable	stage 5 blocker
      4	9	Repeat test case 4,5,6	stage 5 blocker
      4	10	Reboot the device and Agent3 should automatically connect to gateway & client connectivity and internet browsing should happen & no kernel crash/EM agent/onewifi crash	stage 5 blocker
      4	11	Power off the gateway and wait for gateway to up and running and check if Agent 3 onboards to controller via BH without any issues	stage 5 blocker
      4	12	Repeat test case 4,5,6	Stage 5 blocker
      4	13	Change ssid in gateway using cli and wait for 2 to 3 mins and check if same is reflected in agent 3 .if its reflected  Repeat test case 4,5,6	Stage 5 blocker

• Stage 5 (For RDK-B Operators,OEM's,SoC vendors and Third party App companies and system integrators)

  • Tag the code base

    • Banana pi Base build
    • unified-wifi-mesh
    • Onewifi
    • rdk-wifi-hal
    • rdk-wifi-libhostap
    • halinterface

Test app for testers

• https://github.com/cpokuru/testutils-broadband
• 
• test results stored in db 
  • 
• test summary can be saved in text file
  •