The RDKC Media Server is much more than a multi-format, multi-protocol server that delivers your media rich content across multiple screens and platforms. The RDK camera software runs on RPi-0 device. This page dedicated to bringing up and validation of RMS functionality in R-Pi Zero.
- Raspberry Pi 0 Device
- SD Card
- Power Cable
- OTG Cable
- Standard USB keyboard
- Mini HDMI connector
- HDMI Cable
- Television set/monitor with HDMI input
Please refer below link for RPI-0 Environment setup
RDK-C Environment Setup
$ repo init -u "https://code.rdkcentral.com/r/manifests" -m rdkc-nosrc.xml -b rdk-next
$ repo sync
$ source meta-cmf-raspberrypi/setup-environment
select meta-cmf-raspberrypi/conf/machine/raspberrypi0-rdk-camera.conf
$ bitbake rdk-generic-camera-image
$ sudo dd if="Image Name" of="Device Name" bs=4M
Example:
sudo dd if=rdk-generic-camera-image_default_20200130060729.rootfs.rpi-sdimg of=/dev/sdb bs=4M
STEP 1:
Add require SSID and PSK in /etc/wpa_supplicant.conf file in below format
network={
ssid="username"
psk="password"
}
ctrl_interface=/var/run/wpa_supplicant
ctrl_interface_group=0
update_config=1
network={
ssid="XXXX"
psk="YYYYYYYYY"
}
STEP 2:
Reboot the Target
After Reboot don't do step 1 and 2.
Note : Step 1 & 2 is only applicable for fresh target boot-up with new image.
STEP 3:
Modify needed resolution in rms configuration file
Supported Resolution:
SD:
Width - 640 , Height - 480
Width - 720 , Height - 576
HD:
Width - 1280 , Height - 720
FULL HD :
Width - 1920 , Height - 1080
Modify resolution in below configuration file
cd /usr/local/rms/bin
vi rms.conf
RRSIP=XXX.XXX.XXX.XXX
RRSPORT=81
ROOMID=rpi0
RRSSSL=0
WIDTH=1280
HEIGHT=72
After resolution modification need to reboot the target.
Note: This step is not necessary,it is depends on your resolution validation.
STEP 4:
WiFi connection is must needed for RMS validation.
Check WiFi connection by using below command.
ifconfig
root@raspberrypi0-rdk-camera:~# ifconfig
lo Link encap:Local Loopback
inet addr:127.0.0.1 Mask:255.0.0.0
inet6 addr: ::1/128 Scope:Host
UP LOOPBACK RUNNING MTU:65536 Metric:1
RX packets:87 errors:0 dropped:0 overruns:0 frame:0
TX packets:87 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:1000
RX bytes:4552 (4.4 KiB) TX bytes:4552 (4.4 KiB)
wlan0 Link encap:Ethernet HWaddr B8:27:EB:2E:72:2B
inet addr:192.168.43.246 Bcast:192.168.43.255 Mask:255.255.255.0
UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1
RX packets:23 errors:0 dropped:0 overruns:0 frame:0
TX packets:44 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:1000
RX bytes:2893 (2.8 KiB) TX bytes:5887 (5.7 KiB)
STEP 5:
check loaded module by using below command
lsmod
root@raspberrypi0-rdk-camera:~# lsmod
Module Size Used by
bcm2835_v4l2 40563 0
v4l2_common 4809 1 bcm2835_v4l2
videobuf2_vmalloc 6264 1 bcm2835_v4l2
videobuf2_memops 1528 1 videobuf2_vmalloc
videobuf2_v4l2 12640 1 bcm2835_v4l2
videobuf2_core 27389 2 bcm2835_v4l2,videobuf2_v4l2
videodev 154457 4 v4l2_common,videobuf2_core,bcm2835_v4l2,videobuf2_v4l2
media 23307 1 videodev
brcmfmac 258239 0
brcmutil 7590 1 brcmfmac
snd_bcm2835 21405 0
cfg80211 492836 1 brcmfmac
snd_pcm 79872 1 snd_bcm2835
rfkill 19936 3 cfg80211
snd_timer 20294 1 snd_pcm
snd 52949 3 snd_timer,snd_bcm2835,snd_pcm
lirc_rpi 6840 0
lirc_dev 7533 1 lirc_rpi
uio_pdrv_genirq 3469 0
uio 8703 1 uio_pdrv_genirq
fixed 2876 0
sch_fq_codel 9662 2
ipv6 384101 18
STEP 6:
check camera device there or not by using below command
ls /dev/video0
root@raspberrypi0-rdk-camera:~# ls /dev/video0
/dev/video0
STEP 7:
On Bowser of PC:
http://community.dummyersserver.com
Need to modify roomid as rpi0
Press "PLAY" button in WebBrowser page.
We can able to see the capturing content on WebBrowser.
