RDK Resources
[*RDK Preferred*]
Code Management Facility
RDK Forums
[RDK Conferences]
RDK Support
Archives
Papers & Presentations Archive
Page History
...
| SI NO | Automation ID | Steps | Summary | Release |
|---|---|---|---|---|
| 1 | TC-RDKB-WIFI-1011 | 6 | Verify default SSID on devices using SNMP | Release 1 |
| 2 | TC-RDKB-WIFI-BAND-STEERING-1001 | 2 | Validate the default value of band steering Capacity using TR181 data object via WEBPA and verify this Parameter is read only | Release 1 |
| 3 | TC-RDKB-WIFI-ATM-1002 | 4 | Validate AirTimeManagement by Assigning Percentages to the Stations added via dmcli. (2.4Ghz) | Release 1 |
| 4 | TC-RDKB-WIFI-1010 | 6 | Verify default SSID using WebPA | Release 1 |
| 5 | TC-RDKB-WIFI-1016 | 11 | Verify telemetry for wifi channel bandwidth for 2.4G | Release 1 |
| 6 | TC-RDKB-WIFI-MESH-1000 | 7 | Verify Mesh Enable does not change the 5ghz channel to DFS range | Release 1 |
| 7 | TC-RDKB-DEF-SSID-5005 | 4 | Cross-verify the Default Private Wi-Fi SSID and password retrieved from WebPA with the configurations from SNMP | Release 2 |
| 8 | TC-RDKB-MESH-WIFI-1001 | 5 | Verify enabling Bridge Mode using WebPA when the MESH is enabled | Release 2 |
| 9 | TC-RDKB-MESH-WIFI-1002 | 5 | Release 2 | |
| 10 | TC-RDKB-WIFI-RESTORE-1001 | 21 | Verify WiFi settings like SSID ,Network Security mode,Channel Selection Mode,Channel bandwidth,Network name enabled status,Guard interval ,Network active status,Supported Protocols,Radio Status and Radio Channel can be restored to default settings using webpa command for doing WIFI settings reset | Release 3 |
| 11 | TC-RDKB-MESH-WIFI-1004 | 2 | Verify enabling MESH when the Bridge Mode is enabled. | Release 3 |
| 12 | TC-RDKB-WIFI-2050 | 6 | Verify that Wi-Fi connectivity of 5 GHz frequency SSID is not affected when 2.4 GHz frequency SSID is disabled | Release 4 |
| 13 | TC-RDKB-WIFI-1001 | 18 | verify the status of wifi mesh service on enabling and disabling it | Release 4 |
| 14 | TC-RDKB-WIFI-5051 | 24 | Verify Management Frame Power Controls for 2.4 GHz and 5 GHz Radios using WebPA | Release 4 |
| 15 | TC-RDKB-WIFI-ATM-1001 | 3 | Validate AirTimeManagement by Assigning Values at APGroup Level | Release 4 |
| 16 | TC-RDKB-WIFI-TX-RATE-CONFIG-5064 | 17 | To verfiy high power support in 5GHZ band channel | Release 4 |
| 17 | TC-RDKB-WIFI-RESTORE-1002 | 19 | Verify WiFi settings like SSID ,Network Security mode,Channel Selection Mode,Channel bandwidth,Network name enabled status,Guard interval ,Network active status,Supported Protocols,Radio Status and Radio Channel can be restored to default settings using SNMP command for doing WIFI settings reset. | Release 4 |
| 18 | TC-RDKB-WIFI-TX-RATE-CONFIG-5061 | 48 | Verify the configuration of Transmission Control Rate for 2.4 GHz and 5GHz Radio using WebPA | Release 4 |
| 19 | TC-RDKB-WIFI-CON-PERF-1002 | 2 | Find out the average mean time for Wi-Fi connection establishment of 2.4GHz radio band with 20 times | Release 4 |
| 20 | TC-RDKB-WIFI-CON-PERF-1003 | 2 | Find out the average mean time for Wi-Fi connection establishment of 5GHz radio band with 20 times | Release 4 |
| 21 | TC-RDKB-WIFI-4001 | 10 | Ping via IPV4 and IPV6 on 2.4GHz when 5GHz is disabled. | Release 4 |
| 22 | TC-RDKB-WIFI-4002 | 10 | Ping via IPV4 and IPV6 on 5GHz when 2.4GHz is disabled. | Release 4 |
| 23 | TC-RDKB-WIFI-4003 | 12 | Test to verify that LAN side wireless CPE gets an IP address when dual radio bands(2.4GHZ and 5 GHZ) are enabled in CM | Release 4 |
| 24 | TC-RDKB-WIFI-4004 | 20 | Enable/Disable both 2.4GHz, and 5Ghz and confirm Client connects/disconnects successfully | Release 4 |
| 25 | TC-RDKB-WIFI-5001 | 15 | Verify 2.4 GHz WiFi beacon rate changing behavior | Release 4 |
| 26 | TC-RDKB-WIFI-2001 | 6 | Enable/Disable Broadcast SSID for 2.4 Ghz WiFi network and verify disabled status | Release 4 |
| 27 | TC-RDKB-WIFI-2002 | 6 | Enable/Disable Broadcast SSID for 5 Ghz WiFi network and verify disabled status | Release 4 |
Overview
Community Forums
Content Tools
Tasks