...
Prerequisites - One Time Process
Rename/delete the dnsmasq from /usr/bin
Please make sure
1. In /nvram
| Code Block |
|---|
| language | bash |
|---|
| title | nvram prerequest |
|---|
| collapse | true |
|---|
|
cat EasymeshCfg.json
{
"AL_MAC_ADDR": "00:0c:43:26:60:1b",
"Colocated_mode": 0,
"Backhaul_SSID": "mesh_backhaul",
"Backhaul_KeyPassphrase": "test-backhaul",
"sta_4addr_mode_enabled": true
}
cat InterfaceMap.json
{
"PhyList": [
{
"Index": 0,
"RadioList": [
{
"Index": 2,
"RadioName": "wifi2",
"InterfaceList": [
{
"InterfaceName": "wifi2",
"Bridge": "brlan0",
"vlanId": 0,
"vapIndex": 4,
"vapName": "private_ssid_6g"
}
]
},
{
"Index": 1,
"RadioName": "wifi1",
"InterfaceList": [
{
"InterfaceName": "wifi1.1",
"Bridge": "brlan0",
"vlanId": 0,
"vapIndex": 3,
"vapName": "mesh_sta_5g"
},
{
"InterfaceName": "wifi1",
"Bridge": "brlan0",
"vlanId": 0,
"vapIndex": 2,
"vapName": "private_ssid_5g"
}
]
},
{
"Index": 0,
"RadioName": "wifi0",
"InterfaceList": [
{
"InterfaceName": "wifi0.1",
"Bridge": "brlan0",
"vlanId": 0,
"vapIndex": 1,
"vapName": "mesh_backhaul_2g"
},
{
"InterfaceName": "wifi0",
"Bridge": "brlan0",
"vlanId": 0,
"vapIndex": 0,
"vapName": "private_ssid_2g"
}
]
}
]
}
]
}
|
...
| Code Block |
|---|
| language | bash |
|---|
| title | pre_scipt |
|---|
| collapse | true |
|---|
|
#!/bin/sh
sleep 5
#To update al_mac_addr in EasyMeshCfg.json to avoid onewifi restarting during fresh boot-up
#wan_mac="$(cat /sys/class/ieee80211/phy0/macaddress)"
#old_al_mac_addr=`cat /nvram/EasymeshCfg.json | grep AL_MAC_ADDR | cut -d '"' -f4`
#if [ "$old_al_mac_addr" == "00:00:00:00:00:00" ]; then
# sed -i "s/$old_al_mac_addr/$wan_mac/g" /nvram/EasymeshCfg.json
#fi
iw phy phy0 interface add wifi0 type __ap
iw phy phy0 interface add wifi0.1 type __ap
iw phy phy0 interface add wifi1 type __ap
iw phy phy0 interface add wifi2 type __ap
iw phy phy0 interface add wifi1.1 type __ap
#iw phy phy0 interface add wifi2.1 type __ap
#Obtain the wifi0 mac address
wifi_mac="$(cat /sys/class/ieee80211/phy0/macaddress)"
#Strip the : and increment mac by 1 to get wifi1 macaddress
mac=$(echo $wifi_mac | tr -d ':')
mac_incr=$((0x$mac + 8))
wifi0_mac=$(printf "%012x" $mac_incr | sed 's/../&:/g;s/:$//')
#Increment again by 1 to get wifi2 address
mac_incr=$(($mac_incr + 1))
wifi0_1_mac=$(printf "%012x" $mac_incr | sed 's/../&:/g;s/:$//')
#Increment again by 1 to get wifi2 address
mac_incr=$(($mac_incr + 1))
wifi1_mac=$(printf "%012x" $mac_incr | sed 's/../&:/g;s/:$//')
mac_incr=$(($mac_incr + 1))
wifi1_1_mac=$(printf "%012x" $mac_incr | sed 's/../&:/g;s/:$//')
mac_incr=$(($mac_incr + 1))
wifi2_mac=$(printf "%012x" $mac_incr | sed 's/../&:/g;s/:$//')
#print the mac address
echo $wifi0_mac
echo $wifi1_mac
echo $wifi2_mac
#Update the mac address using ip link command
ifconfig wifi0 down
ifconfig wifi0.1 down
ifconfig wifi1 down
ifconfig wifi1.1 down
ifconfig wifi2 down
ip link set dev wifi0 address $wifi0_mac
ip link set dev wifi0.1 address $wifi0_1_mac
ip link set dev wifi1 address $wifi1_mac
ip link set dev wifi1.1 address $wifi1_1_mac
ip link set dev wifi2 address $wifi2_mac
ifconfig wifi0 up
ifconfig wifi1 up
ifconfig wifi1.1 up
ifconfig wifi2 up
exit 0 |
Remove default onewifi db from /opt/secure/wifi
To run onewifi - systemctl start onewifi
Now, check mesh backhaul connection is established or not for 5G .
Please use below command to check ,
- iw dev wifi1.1 info in Extender 1
- iw dev wifi1.1.sta info in ctrl
- iw dev wifi1.1.sta station dump in ctrl - this command give the Extender1 connected client info
Once above steps are success, then run the agent at Ext 1
systemctl start em_agent
Please wait few min, then check iw dev
All private vaps should be up and running in Ext-1 with default EasyMesh ssid's (i,e private_ssid)
- Start onewifi easymesh agent
| Panel |
|---|
| borderColor | black |
|---|
| borderStyle | dashed |
|---|
| title | onewifi_em_agent( full logs attached below) |
|---|
|
/usr/ccsp/EasyMesh#./onewifi_em_agent
input_listener:646 he_bus open success
input_listener:664 recv data:
{
"Version": "1.0",
"SubDocName": "dml",
"WifiConfig": {
"GASConfig": {
"AdvertisementId": 0,
"PauseForServerResp": true,
"RespTimeout": 5000,
"ComebackDelay": 1000,
"RespBufferTime": 1000,
"QueryRespLengthLimit": 127
}, |
- Check whether agent window receives subdoc decode success
- Check whether AP acquired private_ssid through backhaul
...
