Versions Compared

Old Version 16

changes.mady.by.user Dhivya Priya Murugesan

Saved on

compared with

New Version Current

changes.mady.by.user Dhivya Priya Murugesan

Saved on

Key

  • This line was added.
  • This line was removed.
  • Formatting was changed.

...

A tutorial to set up your environment and Download Source Code

 Hardware Hardware Configurations

Here are some other specifications for the Below are the box configuration for Raspberry Pi 4 Model B 8GB RAM:

  • Processor: Broadcom BCM2711, Quad core Cortex-A72 (ARM v8) 64-bit SoC @ 1.5GHz
  • RAM Memory: 1 GB, 2 GB, 4 GB, or 8 GB LPDDR4-3200 SDRAM
  • Flash Memory: Minimum 8 to 32GB capacity
  • Wireless: 2.4 GHz and 5.0 GHz IEEE 802.11ac wireless, Bluetooth 5.0, BLE
  • Ethernet: Gigabit Ethernet
  • Ports: 2 USB 3.0 ports; 2 USB 2.0 ports
  • Display: 2 × micro-HDMI ports (up to 4kp60 supported)
  • Camera: 2-lane MIPI CSI camera port
  • Operating temperature: 0 – 50 degrees C ambient

...

  • The OpenEmbedded build system should be able to run on Ubuntu 20.0 distribution/other compatible linux distribution with the following versions for Git, tar, and Python.

    • Git 2.25.1 or greater
    • tar 1.30 or greater
    • Python 3.10.4 or greater
    • Coreutils(E.g realpath)

    Note: You should also have about 50 Gbytes of free disk space for building images.

    The essential packages you need for a supported Ubuntu or Debian distribution are shown in the following command:

    $ sudo apt-get install gawk wget git-core diffstat unzip texinfo gcc-multilib \
      build-essential chrpath socat cpio python python3 python3-pip python3-pexpect \
      xz-utils debianutils iputils-ping python3-git python3-jinja2 libegl1-mesa libsdl1.2-dev \
      pylint3 xterm bmap-tools
     
    $ sudo apt-get install git cmake autoconf texinfo openjdk-8-jdk openjdk-8-jre \
      m4 libtool libtool-bin curl pkg-config lib32z1 doxygen
    $ sudo apt-get install gcc-multilib g++-multilib

Configure Git

Upgrade your Git version to 1.8.x or higher

...

Credential configuration

Note: it It is also recommended to put credentials in .netrc when interacting with the repo. (Here in login we need to give public user id which created to login login code.rdkcentral.com)

For Signup - https://wiki.rdkcentral.com/signup.action

A sample .netrc file is illustrated below

...

build-raspberrypi4-64-rdk-android-ipstb-oss/tmp/deploy/images/raspberrypi4-64-rdk-android-ipstb-oss/imagename.wic.bz2

Flashing the RPI Image

  • The micro SD card should be formatted (FAT) before writing the RPI image to it.  The minimum SD card size that can be used is 2GB. 
  • Using dd on linux/macOS:
bzcat <IMAGE_NAME>.wic.bz2 | sudo dd of=/dev/sdb bs=4M iflag=fullblock oflag=direct conv=fsync
  • Using bmaptool:
bzip2 -d <path to ImageName.wic.bz2>
sudo -E bmaptool copy --nobmap <path to ImageName.wic> <path to SD card space>
  
Example:
$ bzip2 -d rdk-ipstb-oss-image_rdk-next_20241208053801.rootfs.wic.bz2
$ sudo -E bmaptool copy --nobmap rdk-ipstb-oss-image_rdk-next_20241208053801.rootfs.wic.bz2 /dev/sda
  • You can also use applications like BalenaEtcher to flash a micro SD card with the RPI image.
  • References
    • RPi4 Serial/UART:
    • J8 connector
    • PIN6 - GND
    • PIN8 - RX
    • PIN10 - TX
    • Baud: 115200 8N1
    • Useful yocto/bitbake commands