RDK Resources
[*RDK Preferred*]
Code Management Facility
RDK Forums
[RDK Conferences]
RDK Support
Archives
Papers & Presentations Archive
Wi-Fi Extender Reference Targets
https://doc.turris.cz/doc/en/troubleshooting/serial_link#turris_omnia
...
NOTE:
shared links and information on taking serial connection and flashing OpenWRT imageIn serial console, press "Enter" key to get into u-boot prompt
Type "version" Run following u-boot command to check the u-boot version
If the version found to be "U-Boot 2015.10-rc2", then type "reset" u-boot command. Then skip this section and move on to sub section(Setting default U-boot environment)
If version is other than U-Boot 2015.10-rc2, follow below steps (derived from https://wiki.debian.org/InstallingDebianOn/TurrisOmnia#Bootloader_update)
...
commands to set default U-boot environment
Code Block | ||
---|---|---|
| ||
env default -a
saveenv
reset |
The Omnia ships with TurrisOS preinstalled. This is an OpenWrt fork with the older Linux 4.4 kernel. It uses btrfs to manage the eMMC flash.
We do not use it in this mode. The RDK-B port is closer to the mainline OpenWrt port, which uses Linux 4.14, and a traditional partition table.
Reflashing procedure from TurrisOS:
Download openwrt-18.06.2-mvebu-cortexa9-turris-omnia-sysupgrade.img.gz and omnia-medkit-openwrt-18.06.2-mvebu-cortexa9-turris-omnia-initramfs.tar.gz from http://downloads.openwrt.org/releases/18.06.2/targets/mvebu/cortexa9/ and copy both files to the root of the flash drive.
Disconnect other USB devices from the Omnia and connect the flash drive to either USB port. (I have only verified this with the USB port at the front).
Hold down the reset button (backside, bottom centre) and plug in the power cord. Wait until the fourth LED lights up (green), then release (before the 5th LED lights up). Please click here to see more detail on rescue modes.
Either use the serial console, or connect a computer to a LAN port (LAN0 to LAN4) of the Turris Omnia with a DHCP client.
From a computer:
Code Block | ||
---|---|---|
| ||
ssh root@192.168.1.1 |
Then, from the ssh session or a serial console:
Code Block | ||
---|---|---|
| ||
mount /dev/sda1 /mnt
sysupgrade /mnt/ |
|
In serial console, press "Enter" key to get into u-boot prompt
Run following u-boot commands to set default U-boot environment
|
The Omnia ships with TurrisOS preinstalled. This is an OpenWrt fork with the older Linux 4.4 kernel. It uses btrfs to manage the eMMC flash.
We do not use it in this mode. The RDK-B port is closer to the mainline OpenWrt port, which uses Linux 4.14, and a traditional partition table.
Reflashing procedure from TurrisOS:
openwrt-18.06.2-mvebu-cortexa9-turris-omnia-sysupgrade.img.gz |
Disconnect other USB devices from the Omnia and connect the flash drive to either USB port. (I have only verified this with the USB port at the front).
Hold down the reset button (backside, bottom centre) and plug in the power cord. Wait until the fourth LED lights up (green), then release (before the 5th LED lights up). Please click here to see more detail on rescue modes.
Either use the serial console, or connect a computer to a LAN port (LAN0 to LAN4) of the Turris Omnia with a DHCP client.
From a computer:
|
Then, from the ssh session or a serial console:
mount /dev/sda1 /mnt
sysupgrade /mnt/openwrt-
18.06
.
2
-mvebu-cortexa9-turris-omnia-sysupgrade.img.gz
Wait another minute for the final OpenWrt image to be flashed. The Turris Omnia will reboot itself and you can remove the flash drive.
The eMMC disk is now regularly partitioned.
...
root
@OpenWrt
:~# fdisk /dev/mmcblk0
Welcome to fdisk (util-linux
2.32
).
Changes will remain in memory only, until you decide to write them.
Be careful before using the write command.
Command (m
for
help): p
Disk /dev/mmcblk0:
7.3
GiB,
7818182656
bytes,
15269888
sectors
Units: sectors of
1
*
512
=
512
bytes
Sector size (logical/physical):
512
bytes /
512
bytes
I/O size (minimum/optimal):
512
bytes /
512
bytes
Disklabel type: dos
Disk identifier:
0x15344058
Device Boot Start End Sectors Size Id Type
/dev/mmcblk0p1 *
2048
35327
33280
16
.3M c W95 FAT32 (LBA)
/dev/mmcblk0p2
36864
561663
524800
256
.3M
83
Linux
Create a new partition for RDK-B.
The devicetree database and the Linux kernel are in the FAT32 partition:
...
root
@OpenWrt
:~# mount /dev/mmcblk0p1 /mnt
root
@OpenWrt
:~# ls -l /mnt
-rwxr-xr-x
1
root root
17353
Aug
17
2018
armada-
385
-turris-omnia.dtb
-rwxr-xr-x
1
root root
2445072
Aug
17
2018
zImage
Copy the kernel in the FAT32 partition.
Reconfigure U-boot to boot from your kernel and root partition.
It is strongly recommend to keep the OpenWrt partition and kernel. If boot fails, it is easy to change the U-boot environment and boot back into OpenWrt.
...
Wait another minute for the final OpenWrt image to be flashed. The Turris Omnia will reboot itself and you can remove the flash drive.
The eMMC disk is now regularly partitioned.
Code Block | ||
---|---|---|
| ||
root@OpenWrt:~# fdisk /dev/mmcblk0
Welcome to fdisk (util-linux 2.32).
Changes will remain in memory only, until you decide to write them.
Be careful before using the write command.
Command (m for help): p
Disk /dev/mmcblk0: 7.3 GiB, 7818182656 bytes, 15269888 sectors
Units: sectors of 1 * 512 = 512 bytes
Sector size (logical/physical): 512 bytes / 512 bytes
I/O size (minimum/optimal): 512 bytes / 512 bytes
Disklabel type: dos
Disk identifier: 0x15344058
Device Boot Start End Sectors Size Id Type
/dev/mmcblk0p1 * 2048 35327 33280 16.3M c W95 FAT32 (LBA)
/dev/mmcblk0p2 36864 561663 524800 256.3M 83 Linux |
Note | ||||
---|---|---|---|---|
| ||||
root@OpenWrt:~# opkg update root@OpenWrt:~# opkg install fdisk |
The devicetree database and the Linux kernel are in the FAT32 partition:
Code Block | ||
---|---|---|
| ||
root@OpenWrt:~# mount /dev/mmcblk0p1 /mnt
root@OpenWrt:~# ls -l /mnt
-rwxr-xr-x 1 root root 17353 Aug 17 2018 armada-385-turris-omnia.dtb
-rwxr-xr-x 1 root root 2445072 Aug 17 2018 zImage |
It is strongly recommend to keep the OpenWrt partition and kernel. If boot fails, it is easy to change the U-boot environment and boot back into OpenWrt(Fail safe OS).
Follow instruction from wiki page(https://wiki.rdkcentral.com/display/RDK/Wifi-Extender+Yocto+Build+Instructions) to make yocto's RDK-B image from yocto workspace in your PC.
Boot into openwrt based linux system in turris omnia board. Its downlink interface will have 192.168.1.1 IP address and have it connected to your PC.
Create a new partitions for RDK-B.
Create one primary partition for zImage. Create another extended partition for holding logical partitions for rootfs and /nvram.
Code Block | ||||
---|---|---|---|---|
| ||||
root@OpenWrt:/# fdisk /dev/mmcblk0
Welcome to fdisk (util-linux 2.28.1).
Changes will remain in memory only, until you decide to write them.
Be careful before using the write command.
Command (m for help): p
Disk /dev/mmcblk0: 7.3 GiB, 7818182656 bytes, 15269888 sectors
Units: sectors of 1 * 512 = 512 bytes
Sector size (logical/physical): 512 bytes / 512 bytes
I/O size (minimum/optimal): 512 bytes / 512 bytes
Disklabel type: dos
Disk identifier: 0x15488508
Device Boot Start End Sectors Size Id Type
/dev/mmcblk0p1 * 2048 35327 33280 16.3M c W95 FAT32 (LBA)
/dev/mmcblk0p2 36864 561663 524800 256.3M 83 Linux
Command (m for help): n
Partition type
p primary (2 primary, 0 extended, 2 free)
e extended (container for logical partitions)
Select (default p):
Using default response p.
Partition number (3,4, default 3):
First sector (35328-15269887, default 563200):
Last sector, +sectors or +size{K,M,G,T,P} (563200-15269887, default 15269887): 596479
Created a new partition 3 of type 'Linux' and of size 16.3 MiB.
Command (m for help): n
Partition type
p primary (3 primary, 0 extended, 1 free)
e extended (container for logical partitions)
Select (default e): e
Selected partition 4
First sector (35328-15269887, default 598016):
Last sector, +sectors or +size{K,M,G,T,P} (598016-15269887, default 15269887):
Created a new partition 4 of type 'Extended' and of size 7 GiB.
Command (m for help): n
All primary partitions are in use.
Adding logical partition 5
First sector (600064-15269887, default 600064):
Last sector, +sectors or +size{K,M,G,T,P} (600064-15269887, default 15269887): +512M
Created a new partition 5 of type 'Linux' and of size 512 MiB.
Command (m for help): n
All primary partitions are in use.
Adding logical partition 6
First sector (1650688-15269887, default 1650688):
Last sector, +sectors or +size{K,M,G,T,P} (1650688-15269887, default 15269887): +64M
Created a new partition 6 of type 'Linux' and of size 64 MiB.
All primary partitions are in use.
Command (m for help): n
All primary partitions are in use.
Adding logical partition 7
First sector (1783808-15269887, default 1783808):
Last sector, +sectors or +size{K,M,G,T,P} (1783808-15269887, default 15269887): +512M
Created a new partition 7 of type 'Linux' and of size 512 MiB.
Command (m for help): p
Disk /dev/mmcblk0: 7.3 GiB, 7818182656 bytes, 15269888 sectors
Units: sectors of 1 * 512 = 512 bytes
Sector size (logical/physical): 512 bytes / 512 bytes
I/O size (minimum/optimal): 512 bytes / 512 bytes
Disklabel type: dos
Disk identifier: 0x15488508
Device Boot Start End Sectors Size Id Type
/dev/mmcblk0p1 * 2048 35327 33280 16.3M c W95 FAT32 (LBA)
/dev/mmcblk0p2 36864 561663 524800 256.3M 83 Linux
/dev/mmcblk0p3 563200 596479 33280 16.3M 83 Linux
/dev/mmcblk0p4 598016 15269887 14671872 7G 5 Extended
/dev/mmcblk0p5 600064 1648639 1048576 512M 83 Linux
/dev/mmcblk0p6 1650688 1781759 131072 64M 83 Linux
/dev/mmcblk0p7 1783808 2832383 1048576 512M 83 Linux
Command (m for help): w
The partition table has been altered.
Calling ioctl() to re-read partition table.
Re-reading the partition table failed.: Resource busy
The kernel still uses the old table. The new table will be used at the next reboot or after you run partprobe(8) or kpartx(8).
root@OpenWrt:/# reboot |
After reboot, format /dev/mmcblk0p3, /dev/mmcblk0p5, /dev/mmcblk0p6 and /dev/mmcblk0p7 as ext2 partitions.
Code Block | ||||
---|---|---|---|---|
| ||||
root@OpenWrt:/# mkfs.ext2 /dev/mmcblk0p3
mke2fs 1.44.1 (24-Mar-2018)
/dev/mmcblk0p3 contains a ext2 file system
last mounted on /mnt on Fri Aug 9 13:56:55 2019
Proceed anyway? (y,N) y
Discarding device blocks: done
Creating filesystem with 16640 1k blocks and 4176 inodes
Filesystem UUID: 1b53ea80-b120-4072-a87e-9e68092ed311
Superblock backups stored on blocks:
8193
Allocating group tables: done
Writing inode tables: done
Writing superblocks and filesystem accounting information: done
root@OpenWrt:/# mkfs.ext2 /dev/mmcblk0p5
mke2fs 1.44.1 (24-Mar-2018)
/dev/mmcblk0p5 contains a ext2 file system
last mounted on / on Fri Aug 9 13:57:53 2019
Proceed anyway? (y,N) y
Discarding device blocks: done
Creating filesystem with 262145 1k blocks and 65792 inodes
Filesystem UUID: 14219ea9-3584-4d61-adb4-8370dd73b5cc
Superblock backups stored on blocks:
8193, 24577, 40961, 57345, 73729, 204801, 221185
Allocating group tables: done
Writing inode tables: done
Writing superblocks and filesystem accounting information: done
root@OpenWrt:/# mkfs.ext2 /dev/mmcblk0p6
mke2fs 1.44.1 (24-Mar-2018)
/dev/mmcblk0p6 contains a ext2 file system
last mounted on /nvram on Fri Aug 9 13:59:29 2019
Proceed anyway? (y,N) y
Discarding device blocks: done
Creating filesystem with 65536 1k blocks and 16384 inodes
Filesystem UUID: df6ac518-0a1a-432a-a921-d6958307340a
Superblock backups stored on blocks:
8193, 24577, 40961, 57345
Allocating group tables: done
Writing inode tables: done
Writing superblocks and filesystem accounting information: done
root@OpenWrt:/# mkfs.ext2 /dev/mmcblk0p7
mke2fs 1.44.1 (24-Mar-2018)
Discarding device blocks: done
Creating filesystem with 131072 4k blocks and 32768 inodes
Filesystem UUID: 543d4394-4a94-457a-b487-9c3595d3131e
Superblock backups stored on blocks:
32768, 98304
Allocating group tables: done
Writing inode tables: done
Writing superblocks and filesystem accounting information: done |
...
root@OpenWrt:~
# opkg update
root@OpenWrt:~
# opkg install fdisk
Create one primary partition for zImage. Create another extended partition for holding logical partitions for rootfs and /nvram.
...
Copy zImage, dtb and a rootfs tar file from yocto workspace to turris omnia(whose IP is 192.168.1.1).
(in your PC)
Code Block | ||
---|---|---|
| ||
$ scp <yocto_workspace>build-turris/tmp/deploy/images/turris/zImage root@192.168.1.1:/tmp |
...
$ scp <yocto_workspace>build-turris/tmp/deploy/images/turris/{"zImage-",""}armada-385-turris-omnia.dtb root@192.168.1.1:/tmp/armada-385-turris-omnia.dtb |
...
$ scp <yocto_workspace>build-turris/tmp/deploy/images/turris/rdkb-generic-broadband-image_default_<image-timestamp>.rootfs.tar.gz root@192.168.1.1:/tmp/ |
(in turris omnia)
Code Block | ||
---|---|---|
| ||
root@OpenWrt: |
...
~# mount /dev/mmcblk0p3 /mnt |
...
root@OpenWrt: |
...
~# mv /tmp/zImage /mnt |
...
root@OpenWrt: |
...
~# mv /tmp/armada-385-turris-omnia.dtb /mnt |
...
root@OpenWrt: |
...
~# umount /mnt |
...
root@OpenWrt: |
...
~# mount /dev/mmcblk0p5 /mnt |
...
root@OpenWrt: |
...
~# tar -xzf /tmp/rdkb-generic-broadband-image_default_<image-timestamp>.rootfs.tar.gz -C /mnt |
...
root@OpenWrt: |
...
~# umount /mnt |
...
root@OpenWrt: |
...
~# reboot |
Press enter while turris omnia reboots to get u-boot prompt. Then type following u-boot commands for booting yocto based RDKB image instead of openwrt image.
Code Block | ||
---|---|---|
| ||
=> env set yocto_bootargs earlyprintk console=ttyS0,115200 root=/dev/mmcblk0p5 rootfstype=ext2 rw rootwait |
...
=> env set yocto_mmcload setenv bootargs \"\$yocto_bootargs cfg80211.freg=\$regdomain\"\; ext2load mmc 0:3 0x01000000 zImage\; ext2load mmc 0:3 0x02000000 armada-385-turris-omnia.dtb |
...
=> env set mmcboot run yocto_mmcload \|\| run openwrt_mmcload \|\| run factory_mmcload\; bootz 0x01000000 - 0x02000000 |
...
=> saveenv |
...
=> reset |
Now, Turris Omnia will boot with Yocto based RDKB image.
RDK firmware upgrade with XConf server: Firmware upgrade through XCONF server - Turris-Omnia - User Manual - 2020 - M6
Copy zImage, dtb file and rootfs files(not *dbg* rootfs file) from PC or VM to /tmp/ directory of Turris Omnia which is currently running RDK Image.
For example
Code Block | ||
---|---|---|
| ||
scp zImage--4.14.22-r0-turris-20200720105910.bin root@<TurrisOmnia-IP>:/tmp/ scp armada-385-turris-omnia.dtb root@<TurrisOmnia-IP>:/tmp/ |
...
scp rdkb-generic-broadband-image_default_20200720105910.rootfs.tar.gz root@<TurrisOmnia-IP>:/tmp/ |
In Turris Omnia, execute /lib/rdk/TurrisFwUpgrade.sh to flash new RDK image present in /tmp folder
Code Block | ||
---|---|---|
| ||
sh /lib/rdk/TurrisFwUpgrade.sh |
Go back to OpenWrt OS (please refer Fallback to OpenWrt OS section above below ).
Have Ethernet connection from your PC to LAN port of Turris Omnia.
Keep rootfs(rdkb-generic-broadband-image_default_*.rootfs.tar.gz) and , zImage(zImage--4.14.22-r0-turris-*.bin) files and dtb file in home directory of your PC.
In OpenWrt OS, create a script(yocto-fw-upgrade.sh) with following commands with updates as it needs.
Code Block | ||
---|---|---|
| ||
MYPC_IP=192.168.1.83 |
...
USER_NAME=manigandan |
...
scp $USER_ |
...
NAME@$MYPC_IP:* |
...
$1* /tmp/ |
...
mount /dev/mmcblk0p3 /mnt mv /tmp/zImage-* /mnt |
...
/zImage mv /tmp/ |
...
armada-385-turris-omnia.dtb /mnt/ |
...
umount /mnt |
...
mount /dev/mmcblk0p5 /mnt |
...
rm -rf /mnt/* |
...
tar -xzf /tmp/rdkb-* -C /mnt/ |
...
umount /mnt |
...
reboot |
Run the script from inside OpenWrt OS.
...
Code Block | ||
---|---|---|
| ||
root@OpenWrt:/# ./yocto-fw-upgrade.sh <image-timestamp> |
Press enter while turris omnia reboots to get into u-boot prompt. Then type following u-boot commands to get back to Yocto based RDKB image.
Code Block | ||
---|---|---|
| ||
=> env set yocto_bootargs earlyprintk console=ttyS0,115200 root=/dev/mmcblk0p5 rootfstype=ext2 rw rootwait |
...
=> env set yocto_mmcload setenv bootargs \"\$yocto_bootargs cfg80211.freg=\$regdomain\"\; ext2load mmc 0:3 0x01000000 zImage\; ext2load mmc 0:3 0x02000000 armada-385-turris-omnia.dtb |
...
=> env set mmcboot run yocto_mmcload \|\| run openwrt_mmcload \|\| run factory_mmcload\; bootz 0x01000000 - 0x02000000 |
...
=> saveenv |
...
=> reset |
Turris Omnia will now run upgraded version of Yocto based RDK image.
To fallback to openwrt OS, enter following u-boot commands.
Code Block | ||
---|---|---|
| ||
=> env set mmcboot run openwrt_mmcload \|\| run factory_mmcload\; bootz 0x01000000 - 0x02000000 |
...
=> saveenv |
...
=> reset |