Page History

...

• In PC, keep/configure your Ethernet interface in "Shared to other computers" mode. Tap the interface to bring the change into effect
• Connect an Ethernet cable from your PC(where uboot-turris-omnia-spl.kwb file is hosted on tftp server) to WAN port of Turris Omnia

• Then, run the following commands at the u-boot prompt on Turris Omnia

  dhcp
tftpboot 0x1000000

  Code Block
  language bash theme DJango
  dhcp tftpboot 0x1000000 uboot-turris-omnia-spl.kwb

  
  

  sf probe

  
  

  sf update 0x1000000 0 $filesize

  
  

Setting default U-boot environment

...

Run following u-boot commands to set default U-boot environment

env default -a

...

saveenv

...

reset

Flashing

The Omnia ships with TurrisOS preinstalled. This is an OpenWrt fork with the older Linux 4.4 kernel. It uses btrfs to manage the eMMC flash.

...

• upgrade through a "medkit" image through the use of a USB stick and pressing the reset button.
• https://openwrt.org/toh/turris_cz.nic/turris_cz.nic_omnia is not entirely accurate, and cannot complete without access to the serial port, due to an error in the factory initialisation of the U-boot environment. Updated procedure:
  • Remove the casing. Connect a TTL serial interface, see "Serial Port Access" above.
  • Format a USB flash drive as ext2.

  • Download openwrt-18.06.2-mvebu-cortexa9-turris-omnia-sysupgrade.img.gz and omnia-medkit-openwrt-18.06.2-mvebu-cortexa9-turris-omnia-initramfs.tar.gz from http://downloads.openwrt.org/releases/18.06.2/targets/mvebu/cortexa9/ and copy both files to the root of the flash drive.

  • Disconnect other USB devices from the Omnia and connect the flash drive to either USB port. (I have only verified this with the USB port at the front).

  • Hold down the reset button (backside, bottom centre) and plug in the power cord. Wait until the fourth LED lights up (green), then release (before the 5th LED lights up). _{Please click here to see more detail on rescue modes.}

  • Wait approximately 2 minutes for the Turris Omnia to flash itself with the temporary image, during which LEDs will change multiple times.

  • Either use the serial console, or connect a computer to a LAN port (LAN0 to LAN4) of the Turris Omnia with a DHCP client.
    From a computer:

    ssh root@192.168.1.1

    Then, from the ssh session or a serial console:

    mount /dev/sda1 /mnt sysupgrade /mnt/openwrt-18.06.2-mvebu-cortexa9-turris-omnia-sysupgrade.img.gz

    
    

  • Wait another minute for the final OpenWrt image to be flashed. The Turris Omnia will reboot itself and you can remove the flash drive.

  • After device reboot. You are now running stock OpenWrt 18.06.2.

...

The eMMC disk is now regularly partitioned.

...

root@OpenWrt:~# fdisk /dev/mmcblk0

...

 
Welcome to fdisk (util-linux 2.32).

...

Changes will remain in memory only, until you decide to write them.

...

Be careful before using the write command.

...

 
Command (m for help): p

...

Disk /dev/mmcblk0: 7.3 GiB, 7818182656 bytes, 15269888 sectors

...

Units: sectors of 1 * 512 = 512 bytes

...

Sector size (logical/physical): 512 bytes / 512 bytes

...

I/O size (minimum/optimal): 512 bytes / 512 bytes

...

Disklabel type: dos

...

Disk identifier:

...

 0x15344058
 
Device         Boot Start    End Sectors   Size Id Type
/dev/mmcblk0p1 *

...

     2048  35327   33280  16.3M  c W95 FAT32 (LBA)
/dev/mmcblk0p2      36864 561663  524800 256.3M 83 Linux

Create a new partition for RDK-B.

The devicetree database and the Linux kernel are in the FAT32 partition:

...

root@OpenWrt:~# mount /dev/mmcblk0p1 /mnt

...

root@OpenWrt:~# ls -l /mnt

...

-rwxr

...

-xr-x    1 root     root         17353 Aug 17  2018 armada-385-turris-omnia.dtb

...

-rwxr-xr-

...

x    1 root     root       2445072 Aug 17  2018 zImage

Copy the kernel in the FAT32 partition.

...

Follow instruction from wiki page(https://wiki.rdkcentral.com/display/RDK/Wifi-Extender+Yocto+Build+Instructions) to make yocto's RDK-B image from yocto workspace in your PC.

Boot into openwrt based linux system in turris omnia board. Its downlink interface will have 192.168.1.1 IP address and have it connected to your PC.

Check whether 'fdisk' command is available in openwrt system. if it is not present, follow below steps to have 'fdisk' command.

Create one primary partition for zImage. Create another extended partition for holding logical partitions for rootfs and /nvram.

root@OpenWrt:/# fdisk /dev/mmcblk0
 
Welcome to fdisk (util-linux 2.28.1).
Changes will remain in memory only, until you decide to write them.
Be careful before using the write command.
 
 
Command (m for help): p
Disk /dev/mmcblk0: 7.3 GiB, 7818182656 bytes, 15269888 sectors
Units: sectors of 1 * 512 = 512 bytes
Sector size (logical/physical): 512 bytes / 512 bytes
I/O size (minimum/optimal): 512 bytes / 512 bytes
Disklabel type: dos
Disk identifier: 0x15488508
 
Device         Boot Start    End Sectors   Size Id Type
/dev/mmcblk0p1 *     2048  35327   33280  16.3M  c W95 FAT32 (LBA)
/dev/mmcblk0p2      36864 561663  524800 256.3M 83 Linux

 
Command (m for help): n
Partition type
   p   primary (2 primary, 0 extended, 2 free)
   e   extended (container for logical partitions)
Select (default p):
Using default response p.
Partition number (3,4, default 3):
First sector (35328-15269887, default 563200):
Last sector, +sectors or +size{K,M,G,T,P} (563200-15269887, default 15269887): 596479
 
Created a new partition 3 of type 'Linux' and of size 16.3 MiB.

Command (m for help): n
Partition type
p primary (3 primary, 0 extended, 1 free)
e extended (container for logical partitions)
Select (default e): e

Selected partition 4
First sector (35328-15269887, default 598016):
Last sector, +sectors or +size{K,M,G,T,P} (598016-15269887, default 15269887):

Created a new partition 4 of type 'Extended' and of size 7 GiB.

Command (m for help): n
All primary partitions are in use.
Adding logical partition 5
First sector (600064-15269887, default 600064):
Last sector, +sectors or +size{K,M,G,T,P} (600064-15269887, default 15269887): +512M

Created a new partition 5 of type 'Linux' and of size 512 MiB.

Command (m for help): n
All primary partitions are in use.
Adding logical partition 6
First sector (1650688-15269887, default 1650688):
Last sector, +sectors or +size{K,M,G,T,P} (1650688-15269887, default 15269887): +64M

Created a new partition 6 of type 'Linux' and of size 64 MiB.

All primary partitions are in use.

Adding logical partition 7
First sector (1783808-15269887, default 1783808):
Last sector, +sectors or +size{K,M,G,T,P} (1783808-15269887, default 15269887): +512M

Created a new partition 7 of type 'Linux' and of size 512 MiB.

Command (m for help): p
Disk /dev/mmcblk0: 7.3 GiB, 7818182656 bytes, 15269888 sectors
Units: sectors of 1 * 512 = 512 bytes
Sector size (logical/physical): 512 bytes / 512 bytes
I/O size (minimum/optimal): 512 bytes / 512 bytes
Disklabel type: dos
Disk identifier: 0x15488508

Device      Boot Start End Sectors Size Id Type
/dev/mmcblk0p1 * 2048 35327 33280 16.3M c W95 FAT32 (LBA)
/dev/mmcblk0p2   36864 561663 524800 256.3M 83 Linux
/dev/mmcblk0p3   563200 596479 33280 16.3M 83 Linux
/dev/mmcblk0p4   598016 15269887 14671872 7G 5 Extended
/dev/mmcblk0p5   600064 1648639 1048576 512M 83 Linux
/dev/mmcblk0p6   1650688 1781759 131072 64M 83 Linux

Command (m for help): w
The partition table has been altered.
Calling ioctl() to re-read partition table.
Re-reading the partition table failed.: Resource busy

The kernel still uses the old table. The new table will be used at the next reboot or after you run partprobe(8) or kpartx(8).

 
root@OpenWrt:/# reboot

...

After reboot, format /dev/mmcblk0p3, /dev/mmcblk0p5 and /dev/mmcblk0p6 as ext2 partitions.

root@OpenWrt:/# mkfs.ext2  /dev/mmcblk0p3
mke2fs 1.44.1 (24-Mar-2018)
/dev/mmcblk0p3 contains a ext2 file system
        last mounted on /mnt on Fri Aug  9 13:56:55 2019
Proceed anyway? (y,N) y
Discarding device blocks: done                           
Creating filesystem with 16640 1k blocks and 4176 inodes
Filesystem UUID: 1b53ea80-b120-4072-a87e-9e68092ed311
Superblock backups stored on blocks:
        8193
 
Allocating group tables: done                           
Writing inode tables: done                           
Writing superblocks and filesystem accounting information: done
 
root@OpenWrt:/# mkfs.ext2  /dev/mmcblk0p5
mke2fs 1.44.1 (24-Mar-2018)
/dev/mmcblk0p5 contains a ext2 file system
        last mounted on / on Fri Aug  9 13:57:53 2019
Proceed anyway? (y,N) y
Discarding device blocks: done                           
Creating filesystem with 262145 1k blocks and 65792 inodes
Filesystem UUID: 14219ea9-3584-4d61-adb4-8370dd73b5cc
Superblock backups stored on blocks:
        8193, 24577, 40961, 57345, 73729, 204801, 221185
 
Allocating group tables: done                           
Writing inode tables: done                           
Writing superblocks and filesystem accounting information: done
 
root@OpenWrt:/# mkfs.ext2  /dev/mmcblk0p6
mke2fs 1.44.1 (24-Mar-2018)
/dev/mmcblk0p6 contains a ext2 file system
        last mounted on /nvram on Fri Aug  9 13:59:29 2019
Proceed anyway? (y,N) y
Discarding device blocks: done                           
Creating filesystem with 65536 1k blocks and 16384 inodes
Filesystem UUID: df6ac518-0a1a-432a-a921-d6958307340a
Superblock backups stored on blocks:
        8193, 24577, 40961, 57345
 
Allocating group tables: done                           
Writing inode tables: done                           
Writing superblocks and filesystem accounting information: done

...

Copy zImage, dtb and a rootfs tar file from yocto workspace to turris omnia(whose IP is 192.168.1.1).
(in your PC)

$ scp <yocto_workspace>build-turris/tmp/deploy/images/turris/zImage root@192.168.1.1:/tmp

...

$ scp <yocto_workspace>build-turris/tmp/deploy/images/turris/zImage-armada-385-turris-omnia.dtb root@192.168.1.1:/tmp/armada-385-turris-omnia.dtb

...

$ scp <yocto_workspace>build-turris/tmp/deploy/images/turris/rdkb-generic-broadband-image_default_<image-timestamp>.rootfs.tar.gz root@192.168.1.1:/tmp/

(in turris omnia)

root@OpenWrt:

...

~# mount /dev/mmcblk0p3 /mnt

...

root@OpenWrt:

...

~# mv /tmp/zImage /mnt

...

root@OpenWrt:

...

~# mv /tmp/armada-385-turris-omnia.dtb /mnt

...

root@OpenWrt:

...

~# umount /mnt

...

root@OpenWrt:

...

~# mount /dev/mmcblk0p5 /mnt

...

root@OpenWrt:

...

~# tar -xzf /tmp/rdkb-generic-broadband-image_default_<image-timestamp>.rootfs.tar.gz -C /mnt

...

root@OpenWrt:

...

~# umount /mnt

...

root@OpenWrt:

...

~# reboot

Press enter while turris omnia reboots to get u-boot prompt. Then type following u-boot commands for booting yocto based RDKB image instead of openwrt image.

=> env set yocto_bootargs earlyprintk console=ttyS0,115200 root=/dev/mmcblk0p5 rootfstype=ext2 rw rootwait

...

=> env set yocto_mmcload setenv bootargs \"\$yocto_bootargs cfg80211.freg=\$regdomain\"\; ext2load mmc 0:3 0x01000000 zImage\; ext2load mmc 0:3 0x02000000 armada-385-turris-omnia.dtb

...

=> env set mmcboot run yocto_mmcload \|\| run openwrt_mmcload \|\| run factory_mmcload\; bootz 0x01000000 - 0x02000000

...

=> saveenv

...

=> reset

Now, Turris Omnia will boot with Yocto based RDKB image.

...

Copy zImage and rootfs files from PC to /tmp/ directory of Turris Omnia which is running RDK Image

For example

scp zImage--4.14.22-r0-turris-20200720105910.bin root@<TurrisOmnia-IP>:/tmp/

...

scp rdkb-generic-broadband-image_default_20200720105910.rootfs.tar.gz root@<TurrisOmnia-IP>:/tmp/

In Turris Omnia, execute /lib/rdk/TurrisFwUpgrade.sh  to flash new RDK image present in /tmp folder

sh /lib/rdk/TurrisFwUpgrade.sh

Approach 3:

Go back to OpenWrt OS (please refer Fallback to OpenWrt OS section above ).

...

In OpenWrt OS, create a script(yocto-fw-upgrade.sh) with following commands with updates as it needs.

MYPC_IP=192.168.1.83

...

USER_NAME=manigandan

...

scp $USER_

...

NAME@$MYPC_IP:*

...

$1* /tmp/

...

mount /dev/mmcblk0p3 /mnt

...

mv /tmp/zImage-* /mnt/zImage

...

umount /mnt

...

mount /dev/mmcblk0p5 /mnt

...

rm -rf /mnt/*

...

tar -xzf /tmp/rdkb-* -C /mnt/

...

umount /mnt

...

reboot

Run the script from inside OpenWrt OS.

...

root@OpenWrt:/# ./yocto-fw-upgrade.sh <image-timestamp>

Press enter while turris omnia reboots to get into u-boot prompt. Then type following u-boot commands to get back to Yocto based RDKB image.

=> env set yocto_bootargs earlyprintk console=ttyS0,115200 root=/dev/mmcblk0p5 rootfstype=ext2 rw rootwait

...

=> env set yocto_mmcload setenv bootargs \"\$yocto_bootargs cfg80211.freg=\$regdomain\"\; ext2load mmc 0:3 0x01000000 zImage\; ext2load mmc 0:3 0x02000000 armada-385-turris-omnia.dtb

...

=> env set mmcboot run yocto_mmcload \|\| run openwrt_mmcload \|\| run factory_mmcload\; bootz 0x01000000 - 0x02000000

...

=> saveenv

...

=> reset

Turris Omnia will now run upgraded version of Yocto based RDK image.

...

To fallback to openwrt OS, enter following u-boot commands.

=> env set mmcboot run openwrt_mmcload \|\| run factory_mmcload\; bootz 0x01000000 - 0x02000000

...

=> saveenv

...

=> reset