Page History

root@RaspberryPi-Gateway:~# cat  /nvram/syscfg.db | grep redirect
block_nat_redirection=1
redirection_flag=true

root@RaspberryPi-Gateway:~# cat  /nvram/syscfg.db | grep 10.0.0.1
HTTPS_Server_IP=10.0.0.1
lan_ipaddr=10.0.0.1
Default_Server_IP=10.0.0.1
HTTP_Server_IP=10.0.0.1

root@RaspberryPi-Gateway:~#  cat  /nvram/syscfg.db | grep PartnerID
PartnerID=RDKM

root@RaspberryPi-Gateway:~# ifconfig erouter0
erouter0  Link encap:Ethernet  HWaddr B8:27:EB:50:C1:CF
          inet addr:192.168.0.4  Bcast:0.0.0.0  Mask:255.255.255.0
          inet6 addr: fe80::ba27:ebff:fe50:c1cf/64 Scope:Link
          UP BROADCAST RUNNING MULTICAST  MTU:1500  Metric:1
          RX packets:238 errors:0 dropped:0 overruns:0 frame:0
          TX packets:276 errors:0 dropped:0 overruns:0 carrier:0
          collisions:0 txqueuelen:1000
          RX bytes:38241 (37.3 KiB)  TX bytes:34078 (33.2 KiB)

root@RaspberryPi-Gateway:~# ifconfig brlan0

root@RaspberryPi-Gateway:~#  dmcli eRT getv Device.DeviceInfo.X_RDKCENTRAL-COM_ConfigureWiFi
CR component name is: eRT.com.cisco.spvtg.ccsp.CR
subsystem_prefix eRT.
getv from/to component(eRT.com.cisco.spvtg.ccsp.pam): Device.DeviceInfo.X_RDKCENTRAL-COM_ConfigureWiFi
Execution succeed.
Parameter    1 name: Device.DeviceInfo.X_RDKCENTRAL-COM_ConfigureWiFi
               type:       bool,    value: false

root@RaspberryPi-Gateway:~#  dmcli eRT getv  Device.DeviceInfo.X_RDKCENTRAL-COM_CaptivePortalEnable
CR component name is: eRT.com.cisco.spvtg.ccsp.CR
subsystem_prefix eRT.
getv from/to component(eRT.com.cisco.spvtg.ccsp.pam): Device.DeviceInfo.X_RDKCENTRAL-COM_CaptivePortalEnable
Execution succeed.
Parameter    1 name: Device.DeviceInfo.X_RDKCENTRAL-COM_CaptivePortalEnable
               type:       bool,    value: true

root@RaspberryPi-Gateway:~# ps | grep lighttpd
 3562 root       0:00 lighttpd -f /var/lighttpd.conf
12172 root       0:00 grep lighttpd

root@RaspberryPi-Gateway:/nvram# cat /nvram/hostapd0.conf
# This is the name of the WiFi interface we configured above
interface=wlan0

 

#wlan0 is part of bridge br0
bridge=brlan0

 

# Use the nl80211 driver with the brcmfmac ( Broadcom BCM4334) driver
driver=nl80211
# This is the name of the network
ssid=RPi3_RDKB-AP0
# Use the 2.4GHz band
hw_mode=g
# Use channel 6
channel=06

 

# Enable 802.11n
ieee80211n=1

 

# Enable WMM
wmm_enabled=1

 

# Enable 40MHz channels with 20ns guard interval
#ht_capab=[HT40][SHORT-GI-20][DSSS_CCK-40]

 

# Accept all MAC addresses
macaddr_acl=0

 

# Use WPA authentication
auth_algs=1
# Require clients to know the network name
ignore_broadcast_ssid=0

 


# Use WPA2
wpa=2

 

# Use a pre-shared key
wpa_key_mgmt=WPA-PSK

 

# The network passphrase
wpa_passphrase=rdk@1234

 

# Use AES, instead of TKIP
wpa_pairwise=TKIP CCMP
rsn_pairwise=TKIP CCMP

 

#set the operating channel bandwidth to 20 MHz
vht_oper_chwidth=0

 

# The list of supported rates in units of 100kbps
supported_rates=10 20 55 110 60 90 120 180 240 360 480 540

 

# Basic rate set in units of 100kbps
basic_rates=10 20

 

#Interface for separate control program. hostapd_cli command will use it when trying to connect with hostapd.
ctrl_interface_group=0
ctrl_interface=/var/run/hostapd0

 

wpa_psk_file=/etc/hostapd/hostapd0.psk
eap_server=1
#wps_state=2
ap_setup_locked=1
ap_pin=45276453
wps_pin_requests=/var/run/hostapd0.pin-req
device_name=Raspberrypi
manufacturer=Broadcom
model_name=RPI-3B
model_number=BCM43438
serial_number=8965324
device_type=6-0050F204-1
os_version=01020300
config_methods=push_button keypad label display