RDK Resources
[*RDK Preferred*]
Code Management Facility
RDK Forums
[RDK Conferences]
RDK Support
Archives
Papers & Presentations Archive
Table of Contents |
---|
Objective is to add a Test Parameter in OneWiFi.
Steps to be followed:
The handle is taken from from TR181-WiFi-USGv2.XML file and Get Parameter API will fetch the respective parameter value from OneWiFi DB.
Example:
Code Block |
---|
File: cosa_wifi_dml.c API: WiFi_GetParamBoolValue if (AnscEqualString(ParamName, "X_RDKCENTRAL-COM_TestParameter", TRUE)) { *pBool = pcfg->test_parameter; return TRUE; } |
Code Snippet
The handle for setting a parameter value is taken from TR181-WiFi-USGv2.XML file and SetParameter API will push the changes. This API either pushes the changes to a queue () or will store values till HAL layer (on driver level)
Example:
Code Block |
---|
File: cosa_wifi_dml.c API: WiFi_SetParamBoolValue if (AnscEqualString(ParamName, "X_RDKCENTRAL-COM_TestParameter", TRUE)) { if(global_wifi_config->global_parameters.test_parameter == bValue) { return TRUE; } wifi_util_dbg_print(WIFI_DMCLI,"%s:%d:test_parameter=%d Value = %d \n",__func__, __LINE__,global_wifi_config->global_parameters.test_parameter,bValue); global_wifi_config->global_parameters.test_parameter = bValue; push_global_config_dml_cache_to_one_wifidb(); push_test_parameter_ctrl_queue(bValue); return TRUE; } |
Code Snippet
Whenever an update is made to the Test Parameter, it must be pushed to the global config dml cache to one WiFiDB, along with its value. From cosa_wifi_dml.c file the control then goes to dml_onewifi_apis.c file.
push_global_config_dml_cache_to_one_wifidb API is the generic API for all parameters, which pushes the value to queue.
Here push_test_parameter_ctrl_queue API is defined specifically for Test Parameter and the value could directly pushed to queue with the above API.
Queue push is happening within push_event_to_ctrl_queue API. This API is invoked each time a queue push is required by respective parameters.
Factory Reset for SSID
Figure: Sequence diagram for factory reset of SSID
Code Block |
---|
root@RaspberryPi-Gateway:~#dmcli eRT getv Device.WiFi.SSID.1.SSID Parameter 1 name: Device.WiFi.SSID.1.SSID type: string, value: RPI_RDKB-AP0 root@RaspberryPi-Gateway:~# dmcli eRT setv Device.WiFi.SSID.1.SSID string RPI_RDKB-AP0_NEW setv from/to component(eRT.com.cisco.spvtg.ccsp.wifi): Device.WiFi.SSID.1.SSID Execution succeed. root@RaspberryPi-Gateway:~# dmcli eRT setv Device.WiFi.ApplyAccessPointSettings bool true setv from/to component(eRT.com.cisco.spvtg.ccsp.wifi): Device.WiFi.ApplyAccessPointSettings Execution succeed. root@RaspberryPi-Gateway:~# dmcli eRT getv Device.WiFi.SSID.1.SSID getv from/to component(eRT.com.cisco.spvtg.ccsp.wifi): Device.WiFi.SSID.1.SSID Execution succeed. Parameter 1 name: Device.WiFi.SSID.1.SSID type: string, value: RPI_RDKB-AP0_NEW |
Code Block |
---|
dmcli eRT setv Device.X_CISCO_COM_DeviceControl.FactoryReset string Router,Wifi,Firewall |
Factory Reset by default value
Factory Reset by default value can be achieved my hard coding the default value.
Figure: Sequence diagram for factory reset of default value
Example :
File: cosa_wifi_apis.c
API: wifi_factory_reset
Factory reset command
Code Block |
---|
dmcli eRT setv Device.X_CISCO_COM_DeviceControl.FactoryReset string Router,Wifi,Firewall |
Factory Reset for all radios params to default
Figure: Sequence diagram for radios param factory reset
Example :
Command :
File: cosa_wifi_apis.c
API: wifi_factory_reset
Factory reset command
Code Block |
---|
dmcli eRT setv Device.X_CISCO_COM_DeviceControl.FactoryReset string Router,Wifi,Firewall |
UNIT TEST RESULTS
Set operation for TestParameter:
Get operation for TestParameter:
Factory reset result for Test Parameter
Before Factory Reset:
After Factory Reset: